Don’t forget about our other 2Wire HG-G info that you might be interested in. Login to 2Wire HG-G Router · Change your 2Wire HG-G IP Address. You might find additional types of support and download options at your service provider’s website. For example, a search for “2Wire” at AT&T’s. Rec’vd my 2wire hg-b and the DSL light is green but will not connect to Internet (Internet light is red or off) I have my username.
|Published (Last):||16 May 2013|
|PDF File Size:||13.54 Mb|
|ePub File Size:||13.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
2Wire 2701HG-G User Manual
The Data Errors panel displays the following information. Information displays below the Link Manager 2701hg-v tree, and includes the following: The radio frequency at&r the access point uses for your wireless network the default is 6.
This manual also for: IP address for example, The Local Network — Status page includes the following information: Page 62 Configuration Key Code The key code associated with the current provisioning settings. The System Details page provides information about your gateway, any enhanced services you may have, and provides a link that you can use to restart your system.
The default gateway is a device your 2Wire gateway communicates with directly to give you access to the Internet. From the Time Zone pull-down menu, select the time zone. Channel 6 is the default, and allowing both to compete on the same channel is a bad idea – give each its own wi-fi channel. It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are at&g resetting your router this way, instead of just rebooting it.
Page To perform a ping or traceroute test: Default factory settings for 2Wire HG-B If you have performed a reset of your HG-B device or not changed the defaults, you should be able to access it with the following settings: To view the System Details page: Let the phone line plugged in.
Manually Configure AT&T HG-B – 2Wire | DSLReports Forums
This manual in whole or in part, may not be reproduced, translated, or reduced to any machine- readable form without prior written approval. Loss of Signal Failures The number of DSL loss of signal failures since the 2wir gateway was last restarted, and the elapsed time since the last loss of signal failure.
Incoming is the speed of data flowing from the Internet to your network; Outgoing is the speed of data flowing from your network to the Internet. These time settings are displayed in the Current Time Settings panel, which shows the current date, time, time zone, and whether the time was automatically or manually configured.
The following table describes the fields. You should manually configure these settings ONLY if you thoroughly understand IP internetworking, because an incorrect configuration can DMZplus can 2wirs be configured for one computer on your home network at a time. Ethernet home network interface, the 2701hg-v of payload bytes received, and the number and percentage of received packets in error.
Viewing Your Broadband Link Summary The Broadband Link Summary page provides general information about the current status of your broadband link connection and your system configuration.
Reviewing Bitloading Management and Diagnostic Console Reviewing Bitloading 2wier Bitloading pane shows the bits loaded per tone for the upstream tones 6 to 31 and downstream tones 32 to spectrum.
2Wire HG-B Default Password & Login, Manuals and Reset Instructions | RouterReset
I have freestanding Series 8 dishwasher. Upstream Rate The speed at which data goes over your broadband connection from your network to the Internet, measured in kilobits per second kbps. This procedure will reconnect using a new IP address on your internet service provider. To access aat&t page, your organization must have the Remote Management feature enabled.
Changing Timeout Parameters The MTU Maximum Transmission Unit is the largest size packet or frame, specified in octets eight-byte bitsthat can be sent from a computer to the network.
2Wire Gateway 2701HG Installation Manual
The Advanced – Static Routes page allows you to manually configure static routes that specify the transmission path data must follow between devices on the gateway network. Home Network Tab Each device on your home network is represented with a computer icon.
During 2Wire gateway restart, System Summary Page Troubleshooting pages allow you to view detailed logs that maintain a record of all significant 2Wire gateway events, and to perform diagnostic tests.
Management and Diagnostic Console Advanced – Detailed Log Page The Advanced — Detailed Log page is a debug log facility modeled after syslog, and provides advanced diagnostic capabilities.
Web Remote Access authenticates at&&t encrypts access between the Web browser and the 2Wire gateway, enabling you to securely access and download important files or manage other enhanced services such as Parental Controls or Firewall Monitor. Primary broadband PPPoA configuration module. Wait about 1 minute and try it with your computer. Wait 10 seconds and plug the power back.