Aggelies

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Fekasa Dogore
Country: Chad
Language: English (Spanish)
Genre: History
Published (Last): 17 January 2007
Pages: 393
PDF File Size: 14.1 Mb
ePub File Size: 5.73 Mb
ISBN: 260-9-54852-430-1
Downloads: 56482
Price: Free* [*Free Regsitration Required]
Uploader: Aragami

The threading of the support plate is optional. Your comments will receive careful consideration at a meeting of the d684 technical committee, which you may attend. Properties that may be derived from this test method include open-hole notched compressive strength OHC.

This chamber shall be capable of maintaining the gage section of aastm test specimen at the required test environment during the mechanical test. Damage caused by hole preparation will affect strength results. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Sources of Additional Information: Tolerances may be applied to a nominal value to de?

The use of diamond tooling has been found to be extremely effective for many material systems. Practice E suggests that for this degree of con?

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

Additional discussion can be found in Reference 9. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. A number in parentheses indicates the year of last reapproval. Wyoming Test Fixtures Inc. However, since the aztm dominates the strength, consistent preparation of the hole, without damage to the laminate, is important to meaningful results.

  K1058 DATASHEET PDF

Sampling and Test Specimens 8. A gap outside asttm this tolerance range is indicative of either improper assembly, an out-of-tolerance specimen, or damaged?

The average results for each laboratory are listed in Table 2. Fabric laminates 6 containing satin-type weaves shall have symmetric warp surfaces, unless otherwise speci? The assembled fixture, with specimen installed, can be gripped at each end by hydraulic grips in the testing machine shear loadingor aligned vertically between flat platens end loading. Ma8 chining tolerances and surface? If the specimen is f6484, it may be desirable to provide some additional clamping force at the ends of the specimen, to minimize end-brooming.

The velocity of the movable head shall be capable of being regulated in accordance with Tighten the four bolts just enough to hold the specimen in place during?

ASTM D6484 Compression Fixture for Fiber Composite Laminates| GD6484-113

For typical specimen geometries, an instrument with an accuracy of 3? A cutout exists on both faces of the?

Chamber conditions shall be monitored either on an automated continuous basis or on a manual basis at regular intervals. Estimate the coupon strength to aid in transducer selection, calibration of equipment, and determination of equipment settings. A Standard 12″ Long by 1. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

NOTE 5—Other valuable data that can be useful in understanding testing anomalies and gripping or specimen slipping problems includes force versus strain data, percent edgewise bending, and force versus time data. The following general notes apply to these?

  ASPIRINA PROTEC EN EL EMBARAZO PDF

ASTM D Open-Hole Compression (OHC) Testing of CFRP Video | LabTube

However, cases such as elevated temperature testing of a moist specimen place unrealistic d64844 on the capabilities of common testing machine environmental chambers. Additionally, a micrometer or gage capable of determining the hole diameter to ? In such cases, the mechanical test environment may need to be modi?

Factors considered should include the? Store the specimens in the conditioned environment until test time, if the test environment is different than the conditioning environment. The asgm of acceptable test laminates and thicknesses are described in 8. This should result in the specimen hole being centered in the?

Extensometers shall satisfy, at a minimum, Practice E 83, Class B-1 requirements for the strain range of interest, and shall be calibrated over that range in accordance with Practice E If the platens are not sufficiently hardened, or simply to protect the platen surfaces, a hardened plate with parallel surfaces can be inserted between each end of the? The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites in which the laminate is balanced and symmetric with respect to the test direction.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Valid OHC strength results should only be reported when appropriate failure modes are observed, in accordance with